Product Description
PLASTDER Fine Render is a single-component, cement-based finishing render reinforced with special additives, suitable for both manual and machine application.
Application Areas
Suitable for indoor and outdoor applications on walls and ceilings. Can be applied to fair-faced concrete, concrete, and rough-rendered mineral-based substrates.
Features and Advantages
- Provides a smooth and uniform surface finish.
- Reduces labour time and improves application efficiency.
- Offers high adhesion and excellent slip resistance on vertical surfaces.
- Suitable for both manual and machine application.
- Ensures consistent quality through its factory-produced formulation.
- Resistant to adverse weather conditions and freeze–thaw cycles.
Technical Data
| Property | Value |
|---|---|
| Appearance / Color | Grey |
| Mixing Ratio | 5.5 – 6.5 L Water / 25 kg |
| Resting Time | 5 – 10 minutes |
| Pot Life (25 °C) | 2 – 3 hours |
| Application Temperature | +5 °C to +35 °C |
| Service Temperature | −20 °C to +70 °C |
| Application Thickness | 2 – 6 mm |
| Compressive Strength (EN 1015-11) | CS IV; ≥ 6 N/mm² |
| Bond Strength (EN 1015-12) | ≥ 1.0 N/mm² |
| Capillary Water Absorption (EN 1015-18) | W1; C ≤ 0.40 kg/(m²·min0.5) |
| Water Vapour Diffusion Resistance Factor (μ) (EN 1015-19) | ≤ 25 |
| Ready for Service | 24 hours |
Application Instructions
- 1
Surface Preparation
The substrate must be sound, fully cured, clean, and free from dust, oil, paint residues, silicone, bitumen, tar, detergents, form-release agents, curing compounds, and any other contaminants that may reduce adhesion. Cracks, voids, and damaged areas should be repaired with a suitable repair mortar before application. On fair-faced concrete substrates, a suitable concrete primer should be applied prior to application to improve adhesion. The substrate should be properly pre-dampened before applying the mortar.
- 2
Mixing
Pour 5.5 – 6.5 L of clean water into a clean mixing container and gradually add 25 kg of Plastder Fine Render. Mix with a low-speed mixer until a homogeneous, lump-free consistency is obtained. Allow the mortar to rest for 5 – 10 minutes, then remix for 1 – 2 minutes before application. The prepared mortar should be used within its 2 – 3 hours pot life.
Important Notes
- The application and ambient temperature should be between +5 °C and +35 °C.
- Do not add cement, lime, gypsum, sand, or any other additives to the prepared mortar.
- Follow the recommended mixing water ratio and do not exceed the specified amount of water.
- Do not apply on surfaces exposed to frost within 24 hours, or to direct sunlight and strong winds.
- After application, protect the surface from frost, snow, and other adverse weather conditions for at least 7 days.
- Where necessary, suitable protective measures should be taken.
Storage and Shelf Life
Store in the original, unopened packaging in a cool, dry place, protected from moisture, frost, and direct sunlight. When stored under appropriate conditions, the shelf life is 12 months from the date of manufacture.
Health and Safety
This product is cement-based and may cause irritation to the skin and eyes. Appropriate personal protective equipment (protective clothing, protective gloves, safety goggles, and a dust mask) should be worn during application. The use of a protective skin cream before starting work is recommended. In case of contact with the eyes, rinse immediately with plenty of clean water and seek medical attention without delay. For detailed safety information, refer to the Safety Data Sheet (SDS).
Documents
- Download
Technical Data Sheet (TR / EN)
PDF · Turkish / English
- Safety Data Sheets (SDS) are available on request from our technical team.
Legal Disclaimer
The information contained in this document is based on our current knowledge and experience. As the storage, application, and service conditions of the product are beyond the manufacturer's control, the user is responsible for ensuring that the product is suitable for its intended use and the substrate before application. Trial applications are recommended where necessary. The manufacturer reserves the right to modify product properties in line with technical developments without prior notice. For the most up-to-date information, please refer to the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
