Product Description
FIXDER+ is a cement-based, fine-textured tile adhesive mortar developed for bonding ceramic and tile coverings to concrete, screeds, and cement-based rendered substrates. It is suitable for application thicknesses of 3–6 mm and is available in grey and white.
Application Areas
FIXDER+ is suitable for horizontal (floor) and vertical (wall) applications in residential, commercial, and institutional buildings.
Features and Advantages
- Easy to prepare and apply.
- Offers high adhesion strength.
- Provides excellent slip resistance on vertical surfaces.
- Reduces labour time and improves application efficiency.
Technical Data
| Property | Value |
|---|---|
| Appearance / Color | Grey, White |
| Mixing Ratio | 6.0 – 6.5 L water / 25 kg |
| Application Temperature | +5 °C to +30 °C |
| Application Thickness | 3 – 6 mm |
| Service Temperature | -20 °C / +80 °C |
| Pot Life | 2 hours |
| Open Time | 30 min |
| Grouting Time | 24 hours |
| Adhesion Strength | |
| Initial | ≥ 0.50 N/mm² |
| After Water Immersion | ≥ 0.50 N/mm² |
| After Heat Aging | ≥ 0.50 N/mm² |
| After Freeze–Thaw Cycles | ≥ 0.50 N/mm² |
| After Open Time | ≥ 0.50 N/mm² |
| Slip (EN 1308) | ≤ 5 mm |
Application Instructions
- 1
Surface Preparation
The substrate must be level, sound, and clean. Dust, oil, dirt, and loose particles must be completely removed. Cracks and damaged areas should be repaired with a suitable repair mortar and allowed to dry for 3 – 4 days before application. Concrete substrates should be lightly pre-dampened; however, standing water must not be allowed on the surface. Smooth surfaces such as marble and ceramic should be roughened to improve adhesion. Suitable primer should be applied on absorbent substrates such as aerated concrete and gypsum boards.
- 2
Mixing
Pour 6.0 – 6.5 L of clean water into a clean mixing container and gradually add 25 kg of FIXDER+. Mix with a low-speed mixer until a homogeneous, lump-free consistency is obtained. Allow the mortar to rest for 3 minutes, then remix for 1 – 2 minutes before application.
Important Notes
- The prepared mortar should be used within 30–40 minutes after application to the substrate.
- The maximum application thickness is 6 mm.
- During application and curing, the ambient and substrate temperatures must be above +5 °C.
- After application, protect the surface from frost, rain, and direct sunlight for the first 12 hours.
- A minimum grout joint width of 3 mm should be maintained, and grouting should be carried out after 24 hours.
- Prepare only the amount of mortar that can be used and apply a suitable primer to gypsum-based and other absorbent substrates before application.
Storage and Shelf Life
Store in the original, unopened packaging in a cool, dry place, protected from moisture, frost, and direct sunlight. When stored under appropriate conditions, the shelf life is 12 months from the date of manufacture.
Health and Safety
This product is cement-based and may cause irritation to the skin and eyes. Appropriate personal protective equipment (protective clothing, protective gloves, safety goggles, and a dust mask) should be worn during application. The use of a protective skin cream before starting work is recommended. In case of contact with the eyes, rinse immediately with plenty of clean water and seek medical attention without delay. For detailed safety information, refer to the Safety Data Sheet (SDS).
Documents
- Download
Technical Data Sheet (TR / EN)
PDF · Turkish / English
- Safety Data Sheets (SDS) are available on request from our technical team.
Legal Disclaimer
The information contained in this document is based on our current knowledge and experience. As the storage, application, and service conditions of the product are beyond the manufacturer's control, the user is responsible for ensuring that the product is suitable for its intended use and the substrate before application. Trial applications are recommended where necessary. The manufacturer reserves the right to modify product properties in line with technical developments without prior notice. For the most up-to-date information, please refer to the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
